In the writeup for the latest Ætherwaves compilation, Synthtopia gives us a mention. Nice (and thank you)! Check the link here
In case you’re interested, we’ve just started a mailing list — here’s a signup form!
It seems that we should have supplied some instructions/hints to go with the rbss, so here are some hints and tips!
The best place to read about how the rbss works is by reading Tom Whitwell’s description of the original Turing Machine. The only difference is that the rbss is implemented in software and the 8/16 step switch is replaced by the length control.
To start with, patch clk out to clk in, set the rate control to around the middle position — the LED should now start flashing. Yes? Great!
Now set the length control to its maximum, and the chance control to the middle. Now we’re all set to do something random.
Connect cv out to the cv input of an oscillator and the output of the oscillator to something you can hear. Hopefully at this point you will hear the pitch of the oscillator randomly fluctuating.
Now change the chance control to its minimum position — this will mean that the random sequence stops changing (you might be able to hear the repeating sequence, but it has 16 steps so it’s not always obvious).
Now gradually reduce the length, and you should hear the sequence becoming shorter as it repeats. If you reduce the length to its minimum, the randomness will stop (because the length is now 1, there is no change between consecutive steps), and it is highly likely that if you increase the length again then you won’t get any randomness until you move the chance control away from its minimum position.
If, instead of reducing the chance control to its minimum, you increase it to the maximum, the sequence now repeats after 32 steps (the sequence flips after 16 steps, so descending runs become ascending runs and vice versa). Reducing the length control shortens the sequence as expected, but when length reaches the minimum you will hear the oscillator pitch flipping between two values.
This is something I’ve been playing with for a little while, and the production firmware has now made this more usable — using the rbss as a source for audio. Check the video (and like and subscribe etc. please!)
So, the first batch of the rbss has sold out (there were less than 10 made, so maybe it’s not so surprising). Next up — and almost ready to start building — is another batch of 10, but this time in yellow, with a different panel design. Here’s a sneak peek:
The LED in the yellow version will actually be red, to tie in with the ’70s colour scheme and a time when all LEDs were red…
Follow announcements about availability over on the AEModular forum which now has a wonkystuff board for product announcements and general chit chat.
What with all of the stuff that’s been happening, I completely forgot to post the latest video demonstrating the wonkystuff rbss module! This one ups the production values by actually using a tripod and recording the sound through a mixer. Wonders will never cease.
As the firmware for the rbss has been refined, we’ve been discovering more neat little tricks that the rbss can do, but those will have to wait for the next video.
Thinking that the rbss might be available as a part-assembled kit for a small reduction in cost — the PCB would come with all of the surface-mount components already soldered, just meaning that the customer would need to solder the connectors and pots, and do the final assembly…
(Also shown: 25x70mm peelable vinyl sticker and 25mm button badge!)
Until we sort out a local supplier, we’ve added a shop over at Spreadshirt with a few wonkystuff variations. Check it out! (we’ve not added any margin, so these are the base prices).
This has been on the roadmap for a while, but we finally put together the first prototype today and are very pleased to announce that it worked first time 🙂 We present the random-bit-shift-sequencer (rbss)
There are a few experiments in here
- our first surface mount module;
- the part translucent panel;
- the first design with in-situ-programming (so we can update the firmware!)
We think that it turned out Ok (all the experiments worked out as hoped, although we have a better panel design and colour scheme planned!)
We received a new batch of PCBs yesterday for the mm33, so they are now shipping again – The shop is here